# # For a description of the syntax of this configuration file, # see the Configure script. # comment 'General setup' bool 'Kernel math emulation' CONFIG_MATH_EMULATION y bool 'Normal harddisk support' CONFIG_BLK_DEV_HD y bool 'XT harddisk support' CONFIG_BLK_DEV_XD n bool 'Networking support' CONFIG_NET y bool 'Filesystem quota support' CONFIG_QUOTA y bool 'Limit memory to low 16MB' CONFIG_MAX_16M n bool 'System V IPC' CONFIG_SYSVIPC y bool 'Use -m486 flag for 486-specific optimizations' CONFIG_M486 y bool 'Kernel support for ELF binaries' CONFIG_BINFMT_ELF y bool 'Do you wish to be offered ALPHA drivers added by Slackware?' ALPHA_SLACK n if [ "$CONFIG_NET" = "y" ]; then comment 'Networking options' bool 'TCP/IP networking' CONFIG_INET y if [ "$CONFIG_INET" "=" "y" ]; then bool 'IP forwarding/gatewaying' CONFIG_IP_FORWARD n comment '(it is safe to leave these untouched)' bool 'PC/TCP compatibility mode' CONFIG_INET_PCTCP n bool 'Reverse ARP' CONFIG_INET_RARP n bool 'Assume subnets are local' CONFIG_INET_SNARL y bool 'Disable NAGLE algorithm (normally enabled)' CONFIG_TCP_NAGLE_OFF n fi bool 'The IPX protocol' CONFIG_IPX n #bool 'Amateur Radio AX.25 Level 2' CONFIG_AX25 n fi comment 'SCSI support' bool 'SCSI support?' CONFIG_SCSI n if [ "$CONFIG_SCSI" = "n" ]; then comment 'Skipping SCSI configuration options...' else comment 'SCSI support type (disk, tape, CDrom)' bool 'Scsi disk support' CONFIG_BLK_DEV_SD y bool 'Scsi tape support' CONFIG_CHR_DEV_ST y bool 'Scsi CDROM support' CONFIG_BLK_DEV_SR n bool 'Scsi generic support' CONFIG_CHR_DEV_SG n comment 'SCSI low-level drivers' bool 'Adaptec AHA152X support' CONFIG_SCSI_AHA152X n bool 'Adaptec AHA1542 support' CONFIG_SCSI_AHA1542 n bool 'Adaptec AHA1740 support' CONFIG_SCSI_AHA1740 n if [ "$ALPHA_SLACK" = "y" ]; then bool 'Adaptec AHA274X/284X support' CONFIG_SCSI_AHA274X n bool 'Always IN2000 SCSI support' CONFIG_SCSI_IN2000 n bool 'EATA-DMA (rev. 2.0b) (DPT,NEC,AT&T) support' CONFIG_SCSI_EATA n fi bool 'BusLogic SCSI support' CONFIG_SCSI_BUSLOGIC n bool 'Future Domain 16xx SCSI support' CONFIG_SCSI_FUTURE_DOMAIN y bool 'Generic NCR5380 SCSI support' CONFIG_SCSI_GENERIC_NCR5380 n bool 'NCR53c7,8xx SCSI support' CONFIG_SCSI_NCR53C7xx n bool 'PAS16 SCSI support' CONFIG_SCSI_PAS16 n bool 'Seagate ST-02 and Future Domain TMC-8xx SCSI support' CONFIG_SCSI_SEAGATE n bool 'Trantor T128/T128F/T228 SCSI support' CONFIG_SCSI_T128 n bool 'UltraStor SCSI support' CONFIG_SCSI_ULTRASTOR n bool '7000FASST SCSI support' CONFIG_SCSI_7000FASST n #bool 'SCSI debugging host adapter' CONFIG_SCSI_DEBUG n fi if [ "$CONFIG_NET" = "y" ]; then comment 'Network device support' bool 'Network device support?' CONFIG_NETDEVICES y if [ "$CONFIG_NETDEVICES" = "n" ]; then comment 'Skipping network driver configuration options...' else bool 'Dummy net driver support' CONFIG_DUMMY n bool 'SLIP (serial line) support' CONFIG_SLIP y if [ "$CONFIG_SLIP" = "y" ]; then bool ' CSLIP compressed headers' SL_COMPRESSED y # bool ' SLIP debugging on' SL_DUMP y fi bool 'PPP (point-to-point) support' CONFIG_PPP y bool 'PLIP (parallel port) support' CONFIG_PLIP n bool 'Load balancing support (experimental)' CONFIG_SLAVE_BALANCING n bool 'Do you want to be offered ALPHA test drivers' CONFIG_NET_ALPHA y bool 'Western Digital/SMC cards' CONFIG_NET_VENDOR_SMC y if [ "$CONFIG_NET_VENDOR_SMC" = "y" ]; then bool 'WD80*3 support' CONFIG_WD80x3 y bool 'SMC Ultra support' CONFIG_ULTRA y fi bool '3COM cards' CONFIG_NET_VENDOR_3COM y if [ "$CONFIG_NET_VENDOR_3COM" = "y" ]; then bool '3c501 support' CONFIG_EL1 y bool '3c503 support' CONFIG_EL2 y if [ "$CONFIG_NET_ALPHA" = "y" ]; then bool '3c505 support' CONFIG_ELPLUS y bool '3c507 support' CONFIG_EL16 y fi bool '3c509/3c579 support' CONFIG_EL3 y fi bool 'Other ISA cards' CONFIG_NET_ISA y if [ "$CONFIG_NET_ISA" = "y" ]; then bool 'AT1500 and NE2100 (LANCE and PCnet-ISA) support' CONFIG_LANCE y bool 'Cabletron E21xx support (not recommended)' CONFIG_E2100 y bool 'DEPCA support' CONFIG_DEPCA y if [ "$CONFIG_NET_ALPHA" = "y" ]; then bool 'EtherExpress support' CONFIG_EEXPRESS y bool 'AT1700 support' CONFIG_AT1700 y bool 'NI5210 support' CONFIG_NI52 y bool 'NI6510 support' CONFIG_NI65 y fi bool 'HP PCLAN support' CONFIG_HPLAN y bool 'NE2000/NE1000 support' CONFIG_NE2000 y bool 'SK_G16 support' CONFIG_SK_G16 y fi bool 'EISA and on board controllers' CONFIG_NET_EISA y if [ "$CONFIG_NET_ALPHA" = "y" ]; then bool 'Ansel Communications EISA 3200 support' CONFIG_AC3200 y fi bool 'Apricot Xen-II on board ethernet' CONFIG_APRICOT y bool 'Pocket and portable adaptors' CONFIG_NET_POCKET y if [ "$CONFIG_NET_POCKET" = "y" ]; then bool 'D-Link DE600 pocket adaptor support' CONFIG_DE600 y bool 'D-Link DE620 pocket adaptor support' CONFIG_DE620 y bool 'AT-LAN-TEC/RealTek pocket adaptor support' CONFIG_ATP y bool 'Zenith Z-Note support' CONFIG_ZNET y fi fi fi comment 'CD-ROM drivers' bool 'Sony CDU31A/CDU33A CDROM driver support' CONFIG_CDU31A n if [ "$ALPHA_SLACK" = "y" ]; then bool 'Sony CDU535 CDROM driver support' CONFIG_CDU535 n bool 'NEC CDR-260 CDROM driver support' CONFIG_NEC260 n fi bool 'Mitsumi CDROM driver support' CONFIG_MCD n bool 'Matsushita/Panasonic CDROM driver support' CONFIG_SBPCD n if [ "$CONFIG_SBPCD" = "y" ]; then bool 'Matsushita/Panasonic second CDROM controller support' CONFIG_SBPCD2 n if [ "$CONFIG_SBPCD2" = "y" ]; then bool 'Matsushita/Panasonic third CDROM controller support' CONFIG_SBPCD3 n if [ "$CONFIG_SBPCD3" = "y" ]; then bool 'Matsushita/Panasonic fourth CDROM controller support' CONFIG_SBPCD4 n fi fi fi comment 'Filesystems' bool 'Standard (minix) fs support' CONFIG_MINIX_FS y bool 'Extended fs support' CONFIG_EXT_FS n bool 'Second extended fs support' CONFIG_EXT2_FS y bool 'xiafs filesystem support' CONFIG_XIA_FS y bool 'msdos fs support' CONFIG_MSDOS_FS y if [ "$CONFIG_MSDOS_FS" = "y" ]; then bool 'umsdos: Unix like fs on top of std MSDOS FAT fs' CONFIG_UMSDOS_FS y fi bool '/proc filesystem support' CONFIG_PROC_FS y if [ "$CONFIG_INET" = "y" ]; then bool 'NFS filesystem support' CONFIG_NFS_FS y fi bool 'ISO9660 cdrom filesystem support' CONFIG_ISO9660_FS y bool 'OS/2 HPFS filesystem support (read only)' CONFIG_HPFS_FS y bool 'System V and Coherent filesystem support' CONFIG_SYSV_FS n comment 'character devices' bool 'Parallel printer support' CONFIG_PRINTER y bool 'Logitech busmouse support' CONFIG_BUSMOUSE n bool 'PS/2 mouse (aka "auxiliary device") support' CONFIG_PSMOUSE y if [ "$CONFIG_PSMOUSE" = "y" ]; then bool 'C&T 82C710 mouse port support (as on TI Travelmate)' CONFIG_82C710_MOUSE y fi bool 'Microsoft busmouse support' CONFIG_MS_BUSMOUSE n bool 'ATIXL busmouse support' CONFIG_ATIXL_BUSMOUSE n bool 'Selection (cut and paste for virtual consoles)' CONFIG_SELECTION y bool 'QIC-02 tape support' CONFIG_QIC02_TAPE n if [ "$CONFIG_QIC02_TAPE" = "y" ]; then bool 'Do you want runtime configuration for QIC-02' CONFIG_QIC02_DYNCONF y if [ "$CONFIG_QIC02_DYNCONF" != "y" ]; then comment '>>> Edit configuration parameters in ./include/linux/tpqic02.h!' else comment '>>> Setting runtime QIC-02 configuration is done with qic02conf' comment '>>> Which is available from ftp://ftp.funet.fi/pub/OS/Linux/BETA/QIC-02/' fi fi bool 'QIC-117 tape support' CONFIG_FTAPE y if [ "$CONFIG_FTAPE" = "y" ]; then int ' number of ftape buffers' NR_FTAPE_BUFFERS 3 fi comment 'Sound' bool 'Sound card support' CONFIG_SOUND n comment 'Kernel hacking' #bool 'Debug kmalloc/kfree' CONFIG_DEBUG_MALLOC n bool 'Kernel profiling support' CONFIG_PROFILE n if [ "$CONFIG_SCSI" = "y" ]; then bool 'Verbose scsi error reporting (kernel size +=12K)' CONFIG_SCSI_CONSTANTS n fi